Forum: MKIII FAQ

Well I hear many people talk of Getting rod knock after doing a engine rebuild. After doing a successfull rebuild, and then gettting knock I was a little worried. Well my knock was caused by a faulty oil pump drive shaft that caused a lack of oil. It always seems to have a reason, but no one ever...

Canadian: - Speedo in km/h - Oil Pressure in kg/mm^2 - Turbo Pressure in mmHg US: - Speedo in MPH - Oil Pressure and Turbo Pressure in PSI

So after replacing my Water Pump, Radiator, Thermostat and some other things I went for a test drive. When I got back.... I started to smell burnt oil. Here is where it was coming from. (This is a 7MGE) So I dug into it further and the cause was a bad/broken Crank Case Cover/Gasket. This...

Please post any wheel questions in here. We're getting 2 wheel questions a day, often asking the same information... I don’t know. Go look for yourself. Tirerack.com lists tire specs for each model of tire. Search for the tire size you think you want and see what tires come back from...

Here's some high res scans for you guys, enjoy!!!

Original post: I threw together a random write-up in this thread one night: http://www.supraforums.com/forum/showthread.php?s=&threadid=185766&highlight=rev+match The other posts are pretty darn useful too. I think this would be very helpful to some. I don't know what you would prefer to...

Mods, can this be moved to the FAQ section? First off this method isn't the quickest but it's the easiest. You will be removing some parts that don't have to be removed but it makes it much easier. You'll need a 10mm socket, 12mm socket, 14mm socket, 14mm wrench (ratcheting wrench is a...

could someone point me to a general faq and buying guide for the mk3?

Be warned, this post may offend. Feel free to skip the rant section and go directly to the how to. Concepts: When you launch your car from a stop there are two main things going on. Transfer of weight from the front to the rear and then hooking. If you want a better launch, you need...

Ok guys, here is a writeup for the MaftPro install w/speed density. instalation is easy and very similar to an safc install. What you need: 1.MAFT Pro base unit 2.AIT sensor

Well this topic has seem to come up alot and after asking the mods if I could get this in the faq I'm hoping to make everyone's lives a little better. next stop world peace! ps this article isn't mine I just happened to find this over on another website. here goes!...

Here is the deal: I’m so sick of the ‘which oil is best’ threads that I’m going to take the time out of my 60-80hr work week to do some testing and put an end to this. I seriously hope that after this people will waist a lot less space on SF with dumb oil Q’s and that SF will start some new ante...

Modification Order, MK3 Supra Turbo There are many possible modification orders, but this staged list is the system I recommend for increasing your 7m-gte's power while maintaining good reliability. Please do not begin modifying unless your car is well maintained and running with no problems...

Short answer. Toysport is a joke. Measured by amichie on theothersupraforum. My BC stage 2 intake cam is in the car ATM. I will measure it when I pull it out. Looks like the 7MGTE intake cam has more lift and about 10 degrees more durataion than the NA cam.

Repair manual: http://www.cygnusx1.net/supra/library/TSRM/ Electronic Parts Catalog (North American cars): http://www.cygnusx1.net/supra/library/EPC/MKIII_NATO/index.html EPC (non North American cars): http://www.cygnusx1.net/supra/library/EPC/MKIII/index.html

As many of you know in 89 the MKIII got a nice new steering wheel, along with many other changes, specifically the cruise switch beside the steering wheel was removed, replaced with a button on the steering wheel and a cruise light on the tach. Many people with pre-89 cars wish to use the new...

Ok, so since I just went through this with another member here at 3am online, I figured I would do a little write up on this subject. If you are doing a head gasket change, DO IT RIGHT! The following is a list of pretty much EVERY THING that you should need when doing a head gasket job AND...