[StSupDog]

Does anyone know if the Map-ECU 2 has more selectable Wide band sensor configurations?

My Uego wasn't in the MAp-ECu v1... Maybe they've added a few more?? :dunno:

http://www.racerpartswholesale.com/uego1000.htm

 

[Josh S]

Does anyone know if the Map-ECU 2 has more selectable Wide band sensor configurations?

My Uego wasn't in the MAp-ECu v1... Maybe they've added a few more?? :dunno:

http://www.racerpartswholesale.com/uego1000.htm

The Uego is not listed in the MAP CAL2 software config.

But, if you know the voltage output to afr translation for the Uego, you can simply edit the .o2 file and input the correct values in Lambda. I assume you can do this with the MAP ECU 1 as well...

 

[StSupDog]

Thank you...Do you know if the voltae output would be in the original packaging? or is it something I will need to ask the makers of the product?

 

[killamike553]

bump, doesnt the map cal 2.3 have aem o2 file?

 

[SupraGodTT]

yes it does

 

[JustinCT]

If for some reason you don't have the file, just go to the map ecu forums and they'll provide you with one. They're pretty good about taking care of that stuff for customers.

 

[SupraGodTT]

Justin is correct.

The file should be there... if you start MapCal v3.0.3 and go into the MapCal Config screen, AEM.o2 should be at the top of the box where you can select your .o2 file.

 

[thedarcsage]

subscribed for easy access

will have to do this soon

 

[IdealSupra]

can someone who has the mapecu v3.0.3 or whatnot bring up the aem.o2 file and post the voltages for it down the board? it would be much appreciated.

thanks!

 

[Powerhouse Racing]

MAP-ECU,"O2",1
0, 0.16, 0.16, 0.62, 0.94, 1.4, 1.72, 2.18, 2.5, 2.96, 3.27, 3.74, 4.05, 4.37, 4.68, 4.99, 5, 0, 0, 0.68, 0.747, 0.786, 0.848, 0.892, 0.953, 0.996, 1.058, 1.1, 1.163, 1.206, 1.249, 1.288, 1.331, 1.362
AEM


That should be all you need to get started!

Regards,

Joe

 

[IdealSupra]

MAP-ECU,"O2",1
0, 0.16, 0.16, 0.62, 0.94, 1.4, 1.72, 2.18, 2.5, 2.96, 3.27, 3.74, 4.05, 4.37, 4.68, 4.99, 5, 0, 0, 0.68, 0.747, 0.786, 0.848, 0.892, 0.953, 0.996, 1.058, 1.1, 1.163, 1.206, 1.249, 1.288, 1.331, 1.362
AEM


That should be all you need to get started!

Regards,

Joe

awesome thanks! do i just copy and paste that entire block of

MAP-ECU,"O2",1
0, 0.16, 0.16, 0.62, 0.94, 1.4, 1.72, 2.18, 2.5, 2.96, 3.27, 3.74, 4.05, 4.37, 4.68, 4.99, 5, 0, 0, 0.68, 0.747, 0.786, 0.848, 0.892, 0.953, 0.996, 1.058, 1.1, 1.163, 1.206, 1.249, 1.288, 1.331, 1.362
AEM

into one of the normal O2 cfg files and save it as AEM to overwrite it and then ill have a new file for the aem. Or do i need to input each one of those into the dashboard section under the logging?

 

[Powerhouse Racing]

You can try and copy it but im pretty sure your going to have to input them as the files I have dont just open up like a fuel map normally would!

let me know if you can copy it over!

Regards,

Joe

 

[1sikXR]

subscribed for easy access

will have to do this soon

ditto...i have the same setup