Supra Forums banner

1 - 11 of 11 Posts

·
Zoom-Zoom
Joined
·
617 Posts
Discussion Starter #1
This stuff needs to go quickly, so all prices are OBO. Post questions either here, you can call me 937-416-3060, PM me, or email me ([email protected]).

Sawblades - 4 of them, 2 with decent tires (Yokohama A-008R's, 2/16"-3/16" tread left), one with a Goodyear tire with belt showing (not in good condition). The sawblades themselves are in decent condition. No noticable curb rash. Some small scratches (nothing that can't be sanded/painted out). Will probably need repainted. 40 + shipping for all of them.


7M-GTE Head, 88, relatively clean (I would have to take a brush or something to it, because it's been through the power washer 5 times or so and I couldn't get it clean), ported somewhere between a street port and a race port. Jobs performed are:

Cleaned (most of the way)
removed flashing
smoothed ports
blended bowls to port
blended guides for smoother flow
Intake ports finished in 80 grit, exhaust in 100 grit
Decked for ultra smooth finish.

Things that I would do before mounting:
Cam bores straightened. The head was bowed when I got it on the cutter. removed almost 0.030" to correct. Head is now ultra smooth where it connects to the block, but I believe that you will need to straighten the cam bores because of the warpage on the rest of the head. Cost for machine work at a local shop is $240.
Valve seats recut. I didn't check them out that much, but as far as I know, they will probably need to be recut, which isn't that hard of a process. Also, the valves need to be lapped to accept the new surface. I'm sure it will run in its current state, but this was recommended from my teacher to do this before installing the valves for a greatly reconditioned head.
Flowed on flow bench. I got before numbers on the head, but I wasn't able to get after port work numbers on the head. There's a local guy that will do it for $40. I'm sure of sizable gains based on the bowl, short side radius and smoothing work I have done.

Price is $150 OBO + shipping. There is alot of money in port work in the heads, and I'm giving that to you at a fraction of the cost. For $200, I'll include one set of valves and valve springs and the cams. Last picture is the various parts that are included with the head.



 

·
Zoom-Zoom
Joined
·
617 Posts
Discussion Starter #2
Stock turbo cams. Need a little re-polishing on on the lobes and bearing surfaces. Otherwise good shape. Price is $50 + shipping.



Lower intake manifold. Cleaned. Looks pretty good. Price is $15 + shipping.



I have 2 full sets of valves. $20 + shipping. Most of them need a little cleaning and look like this:



I have one set of valve springs. $15 + shipping.



I have one set of piston oil squirters. $25 + shipping



Chris.
 

·
Registered
Joined
·
28 Posts
interested on the sawblades, how much to ship to a san antonio buisness 78211
 

·
Zoom-Zoom
Joined
·
617 Posts
Discussion Starter #6
monkihead, I will check shipping tomorrow

SlpyEyedSpoolin, I only have the parts that are listed available for purchase. Thanks.
 

·
Registered
Joined
·
28 Posts
any luck on the shippin' cost? no rush, i can see about sending you boxes too..
 

·
Zoom-Zoom
Joined
·
617 Posts
Discussion Starter #8
Looking like around $150 + or -. If you can send boxes, that's cool too. Might remove some of the cost.
 

·
Zoom-Zoom
Joined
·
617 Posts
Discussion Starter #10
Bump. Please make reasonable offers. I would like this stuff gone, and I could use the money.
 

·
Zoom-Zoom
Joined
·
617 Posts
Discussion Starter #11
All of the head stuff is gone. The Oil squirters are gone. The only thing left are the sawblades. I'm tempted to paint them and sell them for a higher price. Let me know if you want them
 
1 - 11 of 11 Posts
Top