Supra Forums banner

1 - 20 of 20 Posts

·
Registered
Joined
·
2,385 Posts
Discussion Starter #1 (Edited)
Could I get a quote, availability, and shipping time to Las Vegas for the following?

Bushings:
Rear:

Bush Sub Assy - Rear - 48702-14030 - 2 sets
Bush, Rear susp arm #2 - 48725-14020 - 2
Bush, Rear susp arm # 1 - 48725-14010 - 2
Bush, Lower ctl arm - 48725-14010 - 2
Bush Assy, Lower ball - 42210-14010 - 2

Front:
Bush, Upper arm - 48632-14010 - 2 sets

Tie Rod Ends: (both apparently with the same part number)

Rod assy, Tie, RH/LH 45460-19225 - 2

Misc other stuff:
Full set of body moulding clips/screws/retainers (basically, everything needed to install the body trim
Gauge cluster glass
All clips required for a windshield installation
Cruise ctl switch assy, main 84630-14060

Edit: Also need a set (6) of Denso Iridium Power spark plugs, model IQ20

Car is a 1989 Turbo, Canada spec, vin jt2ma71j6k0113073.

I can phone in payment on monday.
 

·
Registered
Joined
·
2,385 Posts
Discussion Starter #2
a couple more:
gasket, water outlet housing: 16343-42020
gasket, water bypass: 16347-42010
gasket, front end plate: 11312-42010 (both numbers 1 and 2 as per epc drawing)
gasket, water pump cover: 16124-42020
 

·
Registered
Joined
·
822 Posts
Does yours have the white package? (need to know for body side mouldings). You need the clips for the windshield mouldings?


I have most of it in a quote for you 410583. Most of it is not readily available so it's going to be some time either way. All that's really quick to get would be those gaskets.
 

·
Registered
Joined
·
2,385 Posts
Discussion Starter #4 (Edited)
yeah, the car has the white package. I need the windshield moulding clips as per the attached drawing.
while I'm at it, I may as well also order seals for the rear differential - my breather plug got clogged and I ended up pushing all the fluid out of the differential - I need the appropriate seals for the differential output shafts (not really sure which ones I need)
May as well throw in a lsd sticker 41991-04030
and turbo badge: 75451-14141

I may as well get it shipped all at once to my home address - I assume it is in my account, but if not, I can supply it again.

**edit** remove #2 rear suspension arm bushings from the quote
 

·
Registered
Joined
·
822 Posts
Any chance you could shoot me a fax number and have me just fax you the quote? I can also have it scanned and emailed, it's a bit messy for that number of parts to try to get it on a forum post.
 

·
Registered
Joined
·
2,385 Posts
Discussion Starter #7
Any chance you could shoot me a fax number and have me just fax you the quote? I can also have it scanned and emailed, it's a bit messy for that number of parts to try to get it on a forum post.

edit: ahh! douche your box, its full.

anyhow, email is adam dot pecush at gmail dot com
 

·
Registered
Joined
·
822 Posts
Should get that email this morning. If I missed anything or something's unclear on it, just let me know.
 

·
Registered
Joined
·
2,385 Posts
Discussion Starter #9
i see in the quote you quoted for a full set of body trim - I don't need the actual trim/moulding itself, I just need all of the trim-to-body fasteners (referenced by shape in the following drawing eg: the stars, triangles, circles, etc)
 

·
Registered
Joined
·
2,385 Posts
Discussion Starter #11
no, no...not the window mouldings - I need the attachment hardware (nuts, some bolts, plastic plugs/clips) to attach the side body mouldings (which I already have) to the body. - They are on the right side of the diagram, referred to with the shapes which correspond to the appropriate fittings at the bottom of the diagram. 75398A is one of the part numbers listed on that diagram (hollow star)
 

·
Registered
Joined
·
822 Posts
Some of the clips come with the mouldings. The quantity 22 caps on the quote are all of those symbos that are a circle with a white triangle in the center. If you bought the mouldings, the 75398As came with them. The "target" shapes are just nuts with a washer built onto them which would not be something you'd expect to have damaged when removing the old mouldings.
 

·
Registered
Joined
·
2,385 Posts
Discussion Starter #13
If you bought the mouldings, the 75398As came with them. The "target" shapes are just nuts with a washer built onto them which would not be something you'd expect to have damaged when removing the old mouldings.
I had my old mouldings re-finished and most of the 75398As are in less than ideal condition. The "target" shapes and their corresponding bolts were rusted quite badly. Also, the clips holding the trim on in the wheel wells were either lost or damaged. I figure the following is the complete set and is what I need:

75398A x10 (Not the complete part number, just the one from the diagram)
90168-60018x2
90189-06048x2
90467-05045x2
90164-40021x2
90189-04111x2
90467-05045x2
90179-05032x2
90179-05095x6

plus the 22 caps already included.
 

·
Registered
Joined
·
822 Posts
Each.
75398A x10 - 1.00
90168-60018x2 - .45
90189-06048x2 - .63
90467-05045x2 - .80
90164-40021x2 - .45
90189-04111x2 - 1.05
90467-05045x2 - .80
90179-05032x2 - .45
90179-05095x6 - .54
 

·
Registered
Joined
·
2,385 Posts
Discussion Starter #17
thanks a lot. Are you able to email me a revised quote? Just subtract all of the side mouldings from the old one and add those parts in your last post. I'll just have a look over it and then give you a call with my cc. Who should I ask for?

Adam
 

·
Registered
Joined
·
822 Posts
Having it emailed over now. When you call you can ask for me and just reference that quote number (David, in case sig isn't showing).
 

·
Registered
Joined
·
2,385 Posts
Discussion Starter #19
Any update on shipping/eta?

I have a few more parts to order, but I'll just give you a call though.

Adam
 
1 - 20 of 20 Posts
Top