Supra Forums banner
1 - 20 of 31 Posts

· Registered
Joined
·
1,046 Posts
Discussion Starter · #1 · (Edited)
We have had the new motor in for a little while now and finally had some time to start dressing it up a little bit. Here's some new pics of her,

OLD motor- 3 cracked pistons and one with fused rings.




In the process of removal




New motor finally fully built motor/trans



 

· Registered
Joined
·
1,046 Posts
Discussion Starter · #11 ·
aksupra said:
What kind of radiator is that? I am in the market for one right now. :sadance:

Here ya go, 190001200192. Copy that # into ebay and you will have an aluminum radior that is just as thick as the PHR at half the price! All these guys do is build raiators. The quality is excellent.
 

· Registered
Joined
·
1,046 Posts
Discussion Starter · #12 ·
2jzMK3 said:
looks good, any specs on the motor>?
-ITS dual BB 76, has a .84 housing w/ 3.5" discharge)
-HKS manifold
-Veilside replica intake w/ 90mm tb
-4” HKS Titanium exhaust
-4” dp & mp
-TRD motor mounts
-Boost logic tranny
-PI 3800 Torque converter
-Motor was bored 20 over with forged JE pistons & rings shot peened & beam polished rods
-HKS 264 cams
-ported and polished head
-crower titanium valve springs and retainers
-Powerhouse map ecu
-Gforce OBD2 ecu
-Greddy 3 row fmic with 4 row piping
-HKS GT2 60mm wastegate
-Tial 50mm bov
-Twin walboro pumps
-Custom fuel system
-GT Pro fuel rail
-1000 cc injectors
-ARP studs
-aquamist kit for methanol
-HKS EVC 5
-Boost logic crank pulley
-Custom 2 core aluminium radiator
 

· Registered
Joined
·
1,046 Posts
Discussion Starter · #13 ·
NYC 93-2JZGTE said:
Looking good Brian!! :bigthumb:


No fair you've already seen it....jk post some pics of that mirror engine bay damnit!
 

· 95 Hardtopper X 2
Joined
·
2,034 Posts
I like the new pcv set-up, gotta get you to do mine also. Engine bay looks soooo nice :bigthumb:
 

· Single Turbo
Joined
·
1,020 Posts
Nice auto setup. What the HP?
 

· Registered
Joined
·
1,046 Posts
Discussion Starter · #17 ·
MANI009 said:
I like the new pcv set-up, gotta get you to do mine also. Engine bay looks soooo nice :bigthumb:


Yea we can do that mani. I am going to make a custom can for the pcv soon though. I don't know if i like the one we are using right now.
 

· Registered
Joined
·
1,046 Posts
Discussion Starter · #18 ·
StSupDog said:
Looks Great!!! how does that Intake preform? any down sides?



It performs great i guess. Not much to say about it other than it's a big hollow piece of aluminum. :) The only downside i saw that we had to take care of is the inside of manifold was very rough from the casting. The ports were also off from the head so we just ported and polished the whole thing. Can't complain though because we got the intake and tb for 550! Here is a link to 3 pages of pics,

http://www.northeastsyty.com/gallery/view_album.php?set_albumName=album302&page=1
 

· Registered
Joined
·
1,046 Posts
Discussion Starter · #19 ·
4CEDFED22 said:
Nice auto setup. What the HP?


It has not been dyno tuned yet.
 
1 - 20 of 31 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top